
MODELING NOTES FOR ASHRAE STANDARD 140

© Carrier 2023.  All rights reserved.

===============================================================================
A. SOFTWARE INFORMATION
===============================================================================
1. SOFTWARE VENDOR:   Carrier Corporation

2. SOFTWARE NAME:     Carrier Hourly Analysis Program

3. SOFTWARE VERSION:  6.1.0.1054

4. OPERATING SYSTEM REQUIREMENTS:
                      Windows 10,
                      Windows 11
					  
5. APPROX HARD DISK SPACE REQUIRED FOR INSTALLATION:
                      Typical = 1 GB

6. MINIMUM RAM REQUIRED FOR SOFTWARE OPERATION:
                      8 GB

7. MINIMUM DISPLAY MONITOR REQUIREMENTS:
                      XGA with 1024x768 resolution and 256 colors

===============================================================================
B. REPORT BLOCK FOR ALTERNATIVE MODELING METHODS
===============================================================================

NOTE 1 - Adiabatic Bounrady Condition  (5.3.3.4)
---------------------------------------------------------
Simulated Effect:  

Test specifications in 5.3.3.4 requires adding large amount of insulation to the wall, floor and roof assembly to 
model near adiabatic boundary condition.

Alternative Methods: 

Instead of adding insulation to the wall, floor and ceiling material assembly, in the HAP building model,
"unmodeled space" was added on the outside of each surface, in HAP this feature automatically imposes 
adiabatic boundary condition on the surface, therefore it will achieve the same objective as the test
specification.

===============================================================================
C. REPORT BLOCK FOR EQUIVALENT MODELING METHODS
===============================================================================

NONE


===============================================================================
D. REPORT BLOCK FOR USE OF NON-SPECIFIED INPUTS
===============================================================================
 NONE


===============================================================================
E. REPORT BLOCK FOR OMITTED TEST CASES AND RESULTS
===============================================================================

NOTE 1 - Compressor Energy Consumption and Condenser Fan Energy Consumption
         (Section 5.3.3, 5.3.4)
-------------------------------------------------------------------------------
1.1 List the Case(s) where Results Were Omitted, and which Results Were Omitted
    for the Case(s):
	
	In the Annual Sums Table, "Case CE500 Average Daily Outputs" and "Case CE500
	Average Daily Outputs", the compressor energy consumption (Column C)and the
	condenser fan power consumption output(Column D) were omitted, but the total
	comsumption (Clollumn B,  include supply fan, compressor, condenser fan) and 
	the supply fan energy consumption (Column E) are reported.
	
	In the "June 28 Hourly Output-CE300" table, the Conenser Fan Energy Consumption
	(Column D) is omitted, the value reported in column B for compressor includes the 
	compressor and condenser fan energy consumption.

1.2 Explanation for Omitting the Test Case(s) Results:

	In HAP, compressor and condenser fan power are combined, there is no separate output
	for each of them. The combined energy consumption of compressor and condenser fan can
	be calculated by subtracting the supply fan energy consumption (reported in column E) 
	from the total energy consumption (reported in column B). 
	
	In the "June 28 Hourly Output-CE300" table, the total of compressor and condenser fan 
	energy consumption is reported in the Compressor Energy (Column B) since this value is
	relevant and cannot be calculated based on other values in the table.


NOTE 2 - Economizer and compressor Control Strategy (5.3.4.2.2.1)

-------------------------------------------------------------------------------
2.1 List the Case(s) where Results Were Omitted, and which Results Were Omitted
    for the Case(s):
	
	CE410


2.2 Explanation for Omitting the Test Case(s) Results:

	The stated constrategy in 5.3.4.2.2.1 cannot be modeled in the current simulation engine used by HAP.

===============================================================================
F. REPORT BLOCK FOR CHANGES TO SOURCE CODE FOR THE PURPOSE OF RUNNING THE 
   TESTS, WHERE SUCH CHANGES ARE NOT AVAILABLE IN PUBLICLY RELEASED VERSIONS OF 
   THE SOFTWARE
===============================================================================
NOTE 1 - Internal Heat Gain Schedule (5.3.3.6)
-------------------------------------------------------------------------------
1.1 List the Change(s) to the Source Code:
	No modification was made to the source code. However, the changes were made to the HAP 
	generated EnergyPlus input data file to accurately model internal heat gain schedule 
	specified in Table 5-48. The heat gain schedules are converted to EnergyPlus IDF schedule
	objects in CE300_HeatGainSchedule.idf to be incorporated into the HAP generated
	EnergyPlus IDF files manually.

1.2 List the Test Case(s) Relevant to the Change(s) in the Source Code:
	All test cases in Section 5-3B. Following is a list of the test cases and their corresponding 
	internal heat gain schedule files.
	CE300   CE300_HeatGainSchedule.idf
	CE310   CE310_HeatGainSchedule.idf
	CE320   CE300_HeatGainSchedule.idf
	CE330   CE300_HeatGainSchedule.idf
	CE340   CE300_HeatGainSchedule.idf
	CE350   CE300_HeatGainSchedule.idf
	CE360   CE360_SensibleHeatGainSchedule.idf
	CE400   CE300_HeatGainSchedule.idf
	CE420   CE300_HeatGainSchedule.idf
	CE430   CE300_HeatGainSchedule.idf
	CE440   CE300_HeatGainSchedule.idf
	CE500   CE500_HeatGainSchedule.idf
	CE510	CE510_HeatGainScheduleI.idf
	CE520	CE500_HeatGainSchedule.idf
	CE522	CE500_HeatGainSchedule.idf
	CE525	CE500_HeatGainSchedule.idf
	CE530	CE500_HeatGainSchedule.idf
	CE540   CE500_HeatGainSchedule.idf
	CE545   CE500_HeatGainSchedule.idf	
	
1.3 Explanation of Why the Change is Not Included in the Publicly Released 
    Version of the Software:

	HAP currently allows configuring individual 24-hour schedule profiles by day of week and
	by month of year.	It does not allow unique schedules for individual days of the year such
	as required in the test specification.  Therefore to comply with the test specification,
	customizing the EnergyPlus IDF file to use the specified unique schedules is necessary.  
	This applies to all test cases in sections 5.3.3 and 5.3.4.

NOTE 2 - Cooling System Perfrormance (Full load performance: 5.3.3.10.3; Part Load: 5.3.3.10.4)
-------------------------------------------------------------------------------
2.1 List the Change(s) to the Source Code:
	No modification was made to the source code. However, the changes were made to the HAP 
	generated EnergyPlus input data file to accurately model the cooling system performance 
	as specified in the standard.

2.2 List the Test Case(s) Relevant to the Change(s) in the Source Code:
	All test cases in Section 5-3B.

2.3 Explanation of Why the Change is Not Included in the Publicly Released 
    Version of the Software:

	Originally, there is a set of default cooling system full load and part load performance 
	curves built-in to HAP, this set of performance coefficients are different from what is
	specified in 5.3.3.10. To accurately reflect the cooling system performance specified in 
	section 5.3.3.10.3 and 5.3.3.10.4, the performance tables were converted to lookup tables
	(CE100_DX_CoolingCoilData.IDF) and used to replace the HAP default cooling system performance
	data in the HAP generated EnergyPlus IDF files.
	
	Normally a user would not have enough data for the cooling system to develop a set of 
	performance curves or lookup tables. So HAP does not have a user input to specify the 
	part load performance curve for cooling system.

NOTE 3 - Infiltration Schedules (5.3.4.1.2.1, 5.3.4.1.4.1 )
-------------------------------------------------------------------------------
3.1 List the Change(s) to the Source Code:
	No modification was made to the source code. However, the changes were made to the HAP 
	generated EnergyPlus input data file to accurately model infiltration schedule  
	specified in 5.3.4.1.2.1 and 5.3.4.1.4.1. The infiltration schedules are converted to EnergyPlus IDF schedule
	objects in CE320_InfiltrationSchedule.IDF and CE340_InfiltrationSchedule.IDF to be incorporated into the HAP generated
	EnergyPlus IDF files manually.

3.2 List the Test Case(s) Relevant to the Change(s) in the Source Code:
	CE320   CE320_InfiltrationSchedule.IDF
	CE340   CE340_InfiltrationSchedule.IDF
	
3.3 Explanation of Why the Change is Not Included in the Publicly Released 
    Version of the Software:
	
	The test specifications in 5.3.3 and 5.3.4 require the use of scheduled 
	infiltration hour by hour. This is not currently a feature of the HAP user interface.  
	Therefore, to comply with the test specification, the required infiltration schedules 
	were manually added to the HAP-generated EnergyPlus IDF.
	
NOTE 4 - Outdoor Air Fraction Schedules (5.3.4.1.3.1, 5.3.4.1.4.2 )
-------------------------------------------------------------------------------
4.1 List the Change(s) to the Source Code:
	No modification was made to the source code. However, the changes were made to the HAP 
	generated EnergyPlus input data file to accurately model outdoor air fraction schedule  
	specified in 5.3.4.1.3.1 and 5.3.4.1.4.2. The outdoor fraction schedules are converted 
	to EnergyPlus IDF schedule objects in Case_CE330 -VentilationSchedule.idf and CE340 -VentilationSchedule.idf 
	to be incorporated into the HAP generated EnergyPlus IDF files manually.

4.2 List the Test Case(s) Relevant to the Change(s) in the Source Code:
	CE330   Case_CE330 -VentilationSchedule.idf
	CE340   CE340 -VentilationSchedule.idf
	
4.3 Explanation of Why the Change is Not Included in the Publicly Released 
    Version of the Software:

	The test specifications in 5.3.4.1.3.1, 5.3.4.1.4.2 require the use of scheduled 
	outdoor air flow hour by hour. This is not currently a feature of the HAP user interface.  
	Therefore, to comply with the test specification, the required outdoor air flow fraction schedules 
	were manually added to the HAP-generated EnergyPlus IDF.
	
NOTE 5 - Thermostat Setpoint Schedules (5.3.4.1.5.1)
-------------------------------------------------------------------------------
5.1 List the Change(s) to the Source Code:
	No modification was made to the source code. However, the changes were made to the HAP 
	generated EnergyPlus input data file to accurately model thermostat setpoint schedule  
	specified in 5.3.4.1.5.1. The outdoor fraction schedules are converted to EnergyPlus IDF schedule
	objects in CE350_ThermostatCoolingSetpointSchedule.idf to be incorporated into the HAP generated
	EnergyPlus IDF files manually.

5.2 List the Test Case(s) Relevant to the Change(s) in the Source Code:
	Case CE350
	
5.3 Explanation of Why the Change is Not Included in the Publicly Released 
    Version of the Software:

	The test specifications in 5.3.4.1.5.1 require the use of scheduled 
	thermostat setpoint hour by hour. This is not currently a feature of the HAP user interface.  
	Therefore, to comply with the test specification, the required thermostat setpoint schedules 
	were manually added to the HAP-generated EnergyPlus IDF.
	
===============================================================================
G. REPORT BLOCK FOR ANOMALOUS RESULTS
===============================================================================
NONE


===============================================================================
<END OF DOCUMENT>
===============================================================================
